[1.7.4]
Added
• Added Iris node and T-stop calculation when sending TCD packets
• Added cmotion lens support
Changed
• When exporting data as a .fbx file, EZtrack will now use the current timecode when setting a frames time
Fixed
• Fixed lens profiles created from EZtrack calculation errors introduced in version 1.7.1
[1.7.3]
Fixed
• Fixed a bug preventing lighthouse devices input buttons to work correctly
[1.7.2]
Fixed
• Fixed a bug preventing config files saved before version 1.7.1 to be loaded correctly
[1.7.1]
Added
• Added a way to modify the clamp filter behaviour, including the transition duration, and drift compensation
Fixed
• Fixed .fbx exports not using the correct default referential axes
• Fixed .fbx file list being incomplete just after recording
• Fixed current .fbx recording sometimes not displaying the correct duration
[1.7.0]
Added
• TCD output streams are now fully configurable using TCD profiles defined in settings
• Lens profiles from EZprofile can now be imported to configure the lens data sent in TCD packets
• FBX record files, containing data from several rigs can now be recorded and exported
• A special filter can be applied to Lighthouse trackers to remove any jitter when they are in a static position
Changed
• A navigator in read-only mode can now request control upon modifying a protected field
• Freed receivers synchronization has been revamped and their evaluation is now closer to the genlock or internal tick
• Internal management of the Lighthouse devices list has been overhauled to allow for advanced behaviors to be saved in config files
[1.6.13]
Fixed
• Fixed invalid names attributed to vicon subjects (we were previously using the root segment name)
[1.6.12]
Changed
• Updated Antilatency version to 4.0.0
• Disconnected Antilatency how have a “disconnected state” instead of being removed from the list
• Nodes depending on a disconnected device now use the last pose tracked
[1.6.11]
Added
• Compatibility with firmware version 2.20
[1.6.10]
Added
• Added post mortem debugging tools
Fixed
• Fixed lighthouse noise reduction filter usint too much CPU resources
[1.6.9]
Fixed
• Fixed a rare bug which prevented a software update
[1.6.8]
Added
• Roll bar added to 3d view line-up tools
[1.6.7]
Fixed
• Fixed node delay not working properly
• Fixed hardware settings not loaded correctly on autoload
[1.6.6]
Fixed
• Fixed antilatency devices reconnection issues
[1.6.5]
Changed
• Antilatency devices can now be renamed
[1.6.4]
Fixed
• Sensor sizes are now correctly sent in TCD sockets
[1.6.3]
Changed
• Internal communication port is now set automatically
Fixed
• Fixed the compatibility with the Optitrack system
• Fixed 3D view representation of dynamic nodes
• Fixed encodacam “Add channel” button
[1.6.2]
Fixed
• Fixed a bug where EZtrack would not be able to update
• Fixed a bug where Freed nodes would not use settings such as filtering and inversion
• Fixed a bug where EZtrack would not be able to load a config file if a synced freed receiver was to be created
[1.6.1]
Fixed
• Fixed a bug where Lighthouse devices would be swapped after connecting a new device
• Fixed a bug where Lighthouse base stations would have the wrong indicator displayed in the 3D window
[1.6.0]
Added
• Added a way of modifying the network configuration from EZtrackFinder
• Added a noise reduction filter to lighthouse devices
Changed
• Complete licensing system overhaul
• Slightly improved client performances and reliability
[1.5.1]
Added
• Added a button to restore the previous version of EZtrack from the “About” modal.
• EZtrackUpdater will now be updated along the other EZtrack components.
Changed
• The client can now be deactivated from itself
• Improved client performances
Fixed
• Genlock phase can now be reset to 0
[1.5.0]
Added
• OptiTrack plugin
• Vicon plugin
• VectorNav plugin
• Intel Realsense plugin
• Rig list drag & drop
• TCD protocol
Changed
• Every “tracking” nodes have been merged into the “Transform” node
• Moved lighthouse universe sync from its modal to the lighthouse tab
• Header now only displays systems that are connected to EZtrack
• Header now displays the current config file (after loading or saving one)
• Device using inputs have to be declared in a new menu
• The application can now switch between read-only mode and active mode
Fixed
• Genlock phase can now be reset to 0
• Moving nodes should now work as expected
• Inputs can now be collected from more than 2 trackers at the same time (still limited for
controllers).
• Pose and lens buffers are now loaded correctly
• Axes are now displayed with the correct color when viewing data in “freed” mode
[1.4.7]
Added
• Multi-IP output
• VectorNav plugin
[1.4.6]
Fixed
• The 3D view no longer crashes if client performances are poor
[1.4.5]
Changed
• Nodes adaptive filtering settings overhaul
[1.4.4]
Added
• 3D viewer: Line-up tools
[1.4.3]
Fixed
• Input transforms should no longer conflict with rigs default lens settings
[1.4.2]
Fixed
• Nodes should now be movable without risk of duplication
[1.4.1]
Changed
• Log files naming
Fixed
• IP settings spawning a second server when applied
[1.4.0]
Added
• Freed reception
• Transform node
• Added various buffer/phase options
• Current timecode is now displayed in the header
Changed
• Transform position and orientation are now filtered separately
Fixed
• Wrong attribution of lighthouse devices when using the “Add all” button